Well, I sibscribed recently to a FB group dedicated to emergency communications. Its a very nice group.
I do not believe in the FB because it's like the sand. You write something or find something but soon it's hard to find it again.
I like very much to have the possibility to go somewhere and try to make some QSO's. I am not a contester and I appreciate a nice chat with a fellow ham from here or anywhere. Therefore, I realise i really need a "GO-BOX" or a "GO-KIT" able to work all mode, all frequencies from HF to UHF.
Also the kit will be good for RVSU which is a network of hams involved in emergency communications for various NGO's here.
I will tell you my secret: My GO-BOX is on wheels!
It's a Nissan X-Trail "doped" with a lot of ham-stuff.
The main radio is a ICOM IC-7000 mounted in the trunk and the front panel remote. I finally made the permanent setup; the radio is under the trunk hood, bolted with the optional DC filter (OPC-639) and on the HF side I put a choke Balun to reduce the common mode currents from the Codan antenna (or any othe HF antenna) because the IC-7000 remote head is very sensitive to that issue.
The remote head is under the radio; i put it in place with the help of some industrial 3M velcro. In the left side is a small loudspeaker connected to the remote head. I use that velcro also for phones, portable radios etc...
The main attractions is the Codan 9350 auto-tuning antenna. Bulky but with outstanding performance, it's definetly a magnet for everyone's eyes, in march or in parking lot!
I wrote in other post about the custom mount for this antenna and about the connection with ICOM IC-7000 radio.
What I did lately was to put all the important wires in a protection harness.
The main 12V DC is in harness, the RG58 and the command cable for the ATU antenna is in the harness also. Was a little tricky but the final result is amazing!
For VHF and UHF I use quarter wave antennas. I found that if I put a quarter wave on VHF, the same antenna is resonant also in UHF! A MMANA-GAL simulation showed that the UHF angles are somehow elevated but still a +2db at 0-15 deg. over the horizont so the antenna can be used well.
I preffer NMO (New Motorola Mount) for my mobile antennas. This is a special designed mount to accomodate proffessional antennas ant to whitstand to all the special conditions on a mobile setup in full run. Do not ignore that! And also, keep in mind that a fixed mount is BETTER than any magnetic mount.
Here it is a NMO mount, VHF quarter wave antenna.
I was looking for a good battery eliminator but the price was too high and had to buy it from overseas! Hey, I think a little here and I know how to use a solder iron. Or solder station. Or something like that, you figure out...
So I made a very very simple "battery eliminator" or "separator", whatever, from a Schottky power diode. It was a bulky one, I don't know at what current is rated but did'nt burned at 14-16 Amps so must be better than that. In the little Hammond box I put a little 5 LED voltmeter to quick view the main battery status.
The later addition was a little digital voltmeter on a "Y" cable to view the voltage. Both of them are usefull.
The battery have two fuses, one for plus and one for minus.
Some hams think that if they put a single fuse, on the plus side, is enough!
Well, what if you make a shortcircuit between minus cable and the "plus" pole?
That toolbox cand accomodate the ICOM IC-7000 or anything else. In this setup made for Ciucas Trail Running (a 100 km mountain marathon) I have two Motorola mobile radios.
The lower is a GM360 VHF radio to talk to Salvamont (Mountain Rescue) teams and the upper is a DM3600 to use it with the Radioamateurs in the RVSU network (Radioamateurs for Emergency
In order to be able to use a single antenna, a diplexer is used. Is a Diamond 2000 with modified RF cables. The original ones was too bulky and used PL and N connectors.
A lot of hams use amateur equipments for frequencies above the 146 or 148 MHz. They tend to ignore that out of the regular amateur bands, the radios are very ineffective!
I measured a lot of radios and they seems to loose power after 150 MHz and become very insensitive over 155 MHz. That's how they are made... So, in a emergency network I found a little stupid to use deaf and mute radios! Therefore, I will go with proffessional radios for that particular case and the choice is Motorola!
A completion to my HF setup is a AH4 ATU with a collection of wires. I use two lenghts, 8,5 m and 4 m as they are not half-wave, as reccomended by ICOM to use them with AH-4.
The trick here is that I made two lenght of control cable and RF cable (tied together) so I can use 5m or 10m from radio to AH4.
The AH4 can be used for tuning a horizontal antenna (dipole) or a vertical one (erected on a fishpole stick) using 2 equal wires or 4 counterpoises with a vertical radiator. That's why there are 5 cables at the same lenght...
Well, this is my GO-BOX!
4 wheels and radios!
For final, here it is with a strange VHF antenna on the rooftop!
29 august 2014
Kenwood Programing Software FIRMWARE: KDS-100 504XXXXX 4A46 PTT ID Display feature 176.86 KB CURRENT 401XXXXX F7FC Corrects lock up wh...
Icom programming Software GM-110SC rev.1.2. ex1725. IC-3FX 245MHZ THAILAND CB HANDY RADIO, EX2020 REV 1.0. IC-3FGX 80 CHANNELS 245MHZ THA...
Yaesu Vertex Programming Software Yaesu, Standard, Vertex, Stabo, etc,,. YAESU-VERTEX-STANDARD-MARANTZ: Yaesu Handheld Radios: ADMS-1C Ad...
Looks to me like Kenwood decided to comite suicide! In a market divided between Yaesu and Icom as ham equipment producers, each one with ...
LATER EDIT: Here you can find a solution for a "military-like" backpack radio based on FT857D. TIP for mobile useres: Two male RJ...
I added some detailed pictures of the setup: Spacers detail: Antenna solution: Battery solution: I am not intend to make a...